5~22km Range TDD Full Duplex VTX Module for UAV Drone Video Data Link Support OEM
Key Features:
- TDD OFDM full duplex VTX module for video data Link.
- RF Power: 25±2dBm.
- Working Frequency: 806~826HMz, 1428~1468MHz, 2402~2482MHz.
- Support transparent IP Data transmission (2* Ethernet ports).
- Support serial data transmission( 3* TTL/ RS232 uart).
- Audio input and output with codec.
- Without installing an external power amplifier, transmit distance: 500~2000 meter(ground-to-ground), 5~22km(UAV-to-ground).
- Supports Point-to-Point and Point-to-Multipoint Networks or Mesh networks.
VTX module Overview:
HCL-DLB VTX module was designed for video data wireless transmission with two way wireless data link. This OFDM radio module works at 800MHz, 1.4GHz and 2.4GHz bands, with frequency hopping technology (FHSS) to make sure better stability signal communication.
Specifications:
| 5~22km Range TDD Full Duplex VTX Module for UAV Drone Video Data Link Support OEM |
| Modulation | TDD OFDM |
| Frequency | 806~826MHz,1428~1468MHz,2402~2482MHz |
| FHSS | Support |
| Bandwidths | 1.4/3/5/10/20MHz |
| Throughput | Maximum 30Mbps@20MHz |
| RF Transmissioin Power | 25±2 dBm |
| Constellation | QPSK,16QAM,64QAM self adaption |
| Sensitivity | -106dBm(2.4GHz 1Mbps), -108dBm(1.4GHz 1Mbps), -108dBm(800MHz 1Mbps) |
| Ethernet ports | 2 * Ethernet ports for IP data transmission |
| Serial ports | 3 * RS232/ 3 * TTL for serial data transmission |
| Transmission Range | Up to 22km LOS (UAV-to-ground) and 2km LOS(ground-to-ground) |
| Management | Web UI and Control Uart |
| Encryption | AES128 |
| Networking Mode | Point to Point, Point to Multipoint,Relay, Mesh |
| Power Consumption | <4.5W |
| Dimensions | 58*64*13mm |
| Weight | 32g |
| Working Temp. | -20℃ ~ +65℃ |
| Storage Temp. | -40℃ ~ +80℃ |
| Input /Output signal | Description |
| Power in | XT30PW-M connector,DC in/:7~30V |
| Ethernet 1 | 4Pin ZH1.5mm connector |
| Ethernet 2 | RJ45 connector |
| Data uart1 | 3PIN ZH1.5mm connector, TTL 3.3V |
| Data uart2 and uart3 | 6PIN PH1.25mm connector, uart3 works as control uart and data uart, TTL 3.3V |
| Audio input and output | 4PIN PH1.25mm connector |
| USB | Micro USB connector, for software upgrading |
| Switch | TX/RX control signal for outside power amplifier |
| Main-Antenna | TX/RX antenna port ,IPEX |
| Second-Antenna | RX antenna port,IPEX |
| 12V out | On board 12V out(<150mA), for cool fan power supply |
| Power Led | Red,light on normal powered |
| Node Led | Blue, light on when DLB module works as central node |
| Link Led | Light off – indicate that the node is not linked to the wireless network; Red light – indicate that the node is linked, but wireless signal is weak; Orange light – indicate that the node is linked, wireless signal is middle; Green light – indicate that the node is linked, wireless signal is strong. |
Wireless Networking with HCL-DLB module:
DLB VTX module supports two operating modes: Access Node or Central Node. It can be managed through Web UI or AT command via uart3. DLB module supports features of maximum 16 Access Nodes connected to a Central Node. All of the Nodes are in a same wireless LAN and share the whole transmission bandwidth (maximum 30Mbps@20MHz throughput). Data from Central Node to Access Node, we call downlink, and data from Access Node to Central Node, we call uplink. Uplink and downlink stream ratio can be controlled through web UI or AT command. When using DLB module for Point-to-Point transmitting, uplink and downlink share the whole transmission bandwidth (maximum 30Mbps@20MHz throughput) too. DLB module supports networking mode: Point -to-Point, Point-to-Multipoint, Relay, and Mesh (specify mesh version when order).
Point-to-Point networking type:
Point to Multipoint networking type
Relay networking type
Mesh networking type (Specify)
Application:
FAQ
Q1. This VTX module seems to support IP camera, what if I want to use a camera with HDMI or SDI video output?
A: Yes, the default video input is IP RJ45 Ethernet port, if your camera only has HDMI, SDI, AHD or AV output, you need to buy our mini encoder device to encode the video and audio signal into digital data for transmission. At the receiver end, you can connect it directly to your computer or NVR. If you want to output to an HDMI monitor, you can also buy our decoder device to convert the digital data back into HDMI video and audio signals.
Product Tags:
|
|
5~22km Range TDD Video Transmitter Receiver Module with 806~826MHz and 1428~1468MHz Frequency for UAV Drone Video Data Link Images
|
